If you are simply unable to access the oil hole, then you will need to remove the fan from the ceiling, which is a bit more complicated! But it is necessary if your fan has sealed bearings. Turn off the power to the room your fan is in. It should turn off the power to the whole room that your fan is in.
You can also use a handheld circuit tester to be sure that no power is going to the wires. You can buy one on Amazon or at your local home improvement store. If you fan comes with lights, remove them first. You will need a Philips-head screwdriver and a stepladder.
Climb your ladder and unscrew the lighting unit from the fan. Start by removing the screws from the top of the lighting unit by turning them counterclockwise.
You will also need to remove protective wire nuts on the lighting unit. Find an appropriate wrench that will allow you to twist these off. Once these are removed, you should be able to detach the lighting unit from the fan by gently pulling it off. Once the lighting unit is removed, set it out of the way. Use your Philips-head screwdriver to turn the screws counterclockwise to remove them.
Make sure you are removing the screws that attach the blades to the fan. The screws should be on the part of the fan that is still attached to the ceiling and not on the blades themselves these can stay on. As you remove the blade from the fan, set the blade down on the ground or on a table. You can use an electric screwdriver to unscrew the blades more easily. Disconnect the ceiling fan from the ceiling by removing the covering around the motor. Unscrew the screws that are holding the fan's canopy it is the part over the motor.
There will probably be four screws to remove. Remove them with one hand while supporting the fan with your other hand.
Once these screws have been removed, your fan should be able to lower from the ceiling. With your motor lowered, there should be wires connecting the fan to the ceiling. Look for where they connect with a plastic cap. This is where you can disconnect them by unwrapping the caps counterclockwise.
Oil the motor. Find the bearings at the top and the bottom of the motor. You are looking for where the rotating parts meet the stationary parts. There should be a small seam, which is the edge of the bearing. Drip three to four drops of non-detergent electric motor oil into the top bearing. Then, spin the motor around about 10 times so that the oil works into the bearings.
Turn the motor upside down and add a few drops of oil where the blades connect to the motor. Turn the bottom section of the motor 10 times to work the oil into the bearings. Reconnect your motor to the ceiling. Start by reconnecting the electrical wiring. Then screw in the canopy. Then reconnect the fan's blades one at a time.
To attach the screws, you will turn them clockwise. Turn on the power to the room by switching back the breaker so that you can test the fan. Your fan should be working well now. If you are still having problems , you will need to hire a professional. Either someone wired the fan incorrectly, or the "high speed" winding inside of the motor has become inoperable.
It is not uncommon for those tiny winding wires to separate due to long periods of use. Usually if it is a lack of oil, the fan will actually work better on the higher setting.
Not Helpful 2 Helpful 5. First, put something under it to stop the leaking. Then, see if you can take off the fan and try wiping away any excessive oil and then tightening the oil valve. Not Helpful 1 Helpful 4. Include your email address to get a message when this question is answered.
It is recommended that you check the oil reservoir and oil the fan each time you move the location of the fan. When the fan is tipped and moved, oil can easily leak out of the reservoir. Do it just before reinstallation. Helpful 0 Not Helpful 0. Submit a Tip All tip submissions are carefully reviewed before being published. Turn off the power to the whole room before removing your fan. Helpful 5 Not Helpful 3. How do you lubricate an engine? Electric Motor Bearing Lubrication Procedure Ensure the grease gun contains the appropriate lubricant.
Clean the areas around the relief and fill fittings. Remove the grease relief valve or drain plug. Grease the bearing with a calculated amount of grease. Watch for grease coming out the relief port. What oil do you use in an electric motor?
The motor oil formulation is ideal for lubricating the moving parts of electric motors. Why is my ceiling fan so slow? Answer: A faulty capacitor may cause a ceiling fan to run slowly or quit running altogether.
The capacitor should be replaced by an electrician: There are three screws that hold the light kit or switch or housing cap to the bottom of the fan. Remove these screws and take the light kit or housing cap off. Why does my Hunter ceiling fan spin slow? Ceiling fans that operate at speeds slower than normal can have one of four problems.
Two of these issues are mechanical: loss of bearing lubrication and poor blade balance. The other two are electrical: either a bad capacitor or damaged winding. Why is my ceiling fan making humming noise? A ceiling-fan hum is caused by vibrations amplified by fan parts. Ceiling fans circulate the air in a room, making indoor conditions more comfortable, but some owners complain about noises they make.
Many complaints involve a humming noise that doesn't dissipate when the fan is run at a slower speed. How long do Hunter fans last? Exhaust and ceiling fans are estimated to typically last for a maximum of 10 years while air conditioners last for 8 to 15 years.
Do all ceiling fans have oil holes? Some ceiling fans have maintenance-free double sealed ball bearings that never require oiling. Other ceiling fans have a small "oil hole" above the motor. Once you have removed the motor cover, open it using a screwdriver and find the ball bearings. Carefully lubricate the bearings with the appropriate fan lubricant. Once you have completed this procedure, reassemble each and every part and re-install the ceiling fan. The last step is running the fan at average speed to allow the ball bearings to lubricate themselves properly.
This should make the noise disappear. If after inspection you realize that the fan is not the cause of the noise, you should do the following:. Inspect the ceiling fan and ensure that it is appropriately installed. If it is not installed properly and it is hanging loosely, simply tighten it using the right tool usually a simple screwdriver.
If there is no problem with the mounting of the ceiling fan, check the blades. You can do this by wiggling each blade independently to see if it is loose.
Loose blades can cause some squeaking sounds when in motion. Tighten all the loose screws on the blades and this will eliminate the squeaky noises.
Imbalanced fan blades can cause the ceiling fan to wobble and even get loose. If not fixed this can damage the fan or cause it to fall from its mount. Therefore, ensure that all the blades are balanced using a balancing kit that usually comes with the fan. The kit comes with an instruction manual to enable you to balance the blades. Over time, fans accumulate dust and dirt. This can make them lose balance, triggering a squeak. Cleaning and removing the dirt will enable the fan to maintain balance and run effortlessly.
Use a clean piece of cloth to wipe off the dust or dirt. If your ceiling fan is equipped with a light kit, inspect the light kit. Maybe it is the reason why the fan is noisy. When it is operational, the ceiling fan creates motion. If the light kit is loose, the motion will make it vibrate. This will cause a squeak that you might think is coming from the fan motor. Tighten the loose light fixture, check the rubber covering and ensure that it is still in its original place, and tighten the screws that hold the globe in place.
If tightening the screws does not help, you can use a thick rubber band to tie around the neck of the globe and the shade. If the bracket is loose or is not level with the ceiling, there will be a gap between the ceiling and the bracket.
This can be the cause of squeaky noises when the fan is on. Therefore, tighten any loose screws and ensure that the canopy is in the right position. A noisy ceiling fan can be a real nuisance, especially if you are trying to sleep or concentrate on important business. Therefore, inspect the fan as a whole and try to pinpoint one or a few of the sources of the noise.
0コメント